Joyride Hot Rods

12/23/2020

Finally, we have the popular 1937 Ford Custom Tail Light Stands back in stock. Buy just the brackets, or combined with variety of '37 tail lights that are available via our Ebay store or our Website www.joyridehotrods.com

10/21/2019

1937 FORD TAIL LIGHTS - VARIOUS LENSES

08/07/2019

Now available, popular air cleaners for single and double barrel carburetors with different fasteners that make the look so much more nostalgic.
Concave, Domed or Louvered Chrome Air Cleaners for Single or 2 Barrel Carburetors with 2 5/8" or 2 1/16" diameter necks.

The chrome base can fit to 2 5/8" Strombergs or Holley / Edelbrock 94's and then there is a reducing insert included that allows the air cleaner to fit to carbs with a 2 5/16" neck.

Aprox 4 1/2" Diameter, total height 4" with 4" Diameter Paper Elements. Held together with various Bullet, Acorn or Tri-Bar Fasteners.
Also, beautiful quality 4" Helmet or Old School cast Aluminum Finned Air Cleaners available.
Joyride1932 on Ebay or www.joyridehotrods.com

08/07/2019

04/13/2019

3 more colors available!

Now available Vintage Cotton Braid Spark Plug wire for use with modern ELECTRONIC IGNITION SYSTEMS.
CHECK OUT OUR EBAY STORE OR OUR WEBSITE www.joyridehotrods.com
Made in the USA, 7.8mm Lacquer Covered Cotton Braid over EPDM Insulation and Spiral Wound Suppression Core specifically for use with modern electronic ignition systems, including MSD 6A, 6AL Multi Spark Ignition Boxes and Pertronix Electronic Ignition Conversion Kits.
The Lacquer allows you to easily wipe of any dirty hand marks or oil stains.
Please Note: Many of the cheaper 7mm or 8mm wire out there on offer, most probably will not have the suppression core and this will cause problems with the micro chips used in modern electronic ignitions.
Currently sell in a length of 25ft, that is more than adequate for all popular V8 engines with a universal Terminal and Boot kit to allow you to route the wire as you please, cut to length and crimp the terminals yourself. (A correct crimper is recommended but is not included in this kit).
This terminal kit only works with 'Socket' style Distributor Caps.....if you have a 'Post' style distributor cap, they need similar terminals used on spark plugs, let us know and we will exchange the terminals as required.

02/27/2019

Now available Vintage Cotton Braid Spark Plug wire for use with modern ELECTRONIC IGNITION SYSTEMS.

CHECK OUT OUR EBAY STORE OR OUR WEBSITE www.joyridehotrods.com

Made in the USA, 7.8mm Lacquer Covered Cotton Braid over EPDM Insulation and Spiral Wound Suppression Core specifically for use with modern electronic ignition systems, including MSD 6A, 6AL Multi Spark Ignition Boxes and Pertronix Electronic Ignition Conversion Kits.
The Lacquer allows you to easily wipe of any dirty hand marks or oil stains.

Please Note: Many of the cheaper 7mm or 8mm wire out there on offer, most probably will not have the suppression core and this will cause problems with the micro chips used in modern electronic ignitions.

Currently sell in a length of 25ft, that is more than adequate for all popular V8 engines with a universal Terminal and Boot kit to allow you to route the wire as you please, cut to length and crimp the terminals yourself. (A correct crimper is recommended but is not included in this kit).

This terminal kit only works with 'Socket' style Distributor Caps.....if you have a 'Post' style distributor cap, they need similar terminals used on spark plugs, let us know and we will exchange the terminals as required.

4 colors available but more will come in time.
Complete specific engine kits with wires cut and terminals fitted are planned for the near future.

09/29/2018

Really nice touches on this 1940 Ford pickup at the Lone Star Nationals today. Rear roll pan, probably the best I have ever seen. Would like to know if the license plate trim is fabricated or off another vehicle?
The '39 Chevy tail lights shown, I do sell, housing in primer or full chrome, Stock lens, Blue Dot or Red Dot Lens. www.joyridehotrods.com

09/29/2018

08/04/2018

New and available now, one of the most popular hot rod tail lights, the 1937 Ford, fully chromed! With Custom Lens.

08/02/2018

A while ago I posted pictures of awesome stock steering wheels from the 50’s and 60’s. I got a 1963 Oldsmobile for my shop truck. So deep you really need the matching column and control levers. The column is always a little tricky to cut down, not much room at all for the gear shift mechanism and had to fabricate a lower housing section to finish it nicely. Wiring turn, headlamp, horn, and neutral safety not so easy! but worth it.

05/12/2018

Auto swap at Canton. People here and King Julian are so nice! Makes work a pleasure!