Cleared To Land

  • Home
  • Cleared To Land
Call Directions Contact the business

Cleared To Land Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Cleared To Land, Gift Shop, .

The Kiddy Cubs & Kiddy Copter are heading over to EAAs Air Adventure in Oshkosh Wisconsin. We will be located at the Avi...
20/07/2025

The Kiddy Cubs & Kiddy Copter are heading over to EAAs Air Adventure in Oshkosh Wisconsin. We will be located at the Aviation Products Tent (The maker of Pedal Plane Parts) located at the EAA Wearhouse near the Wittman Field Control Tower on July 23rd only. The Pedalventure VI parade is at 2PM the same day. Hope we see you there!

Kiddy Cub Flight Team At The Ada Michigan 4th of July 2024 Independence Day Parade. Thanks Tony Helms & Family & Brian B...
04/07/2024

Kiddy Cub Flight Team At The Ada Michigan 4th of July 2024 Independence Day Parade.
Thanks Tony Helms & Family & Brian Bailey & Family!

Helping PaPa with Annual Inspection of Floatplane.
23/11/2023

Helping PaPa with Annual Inspection of Floatplane.

Check out the making of the Kiddy Copter as presented by MAKE Magagzine;
28/02/2022

Check out the making of the Kiddy Copter as presented by MAKE Magagzine;

In Make:V76, Mike Senese wrote an article, titled "Flight Trainer," in our Made on Earth section. It was about the Kiddy Copter built by Charles Helmholdt

N728DC getting ready to fly after this years annual.  Thanks Tony for helping me get her ready.
28/06/2020

N728DC getting ready to fly after this years annual. Thanks Tony for helping me get her ready.

When putting my airplane on floats it became necessary to have a way to pull it out of the hanger.  It's either a two ma...
19/02/2020

When putting my airplane on floats it became necessary to have a way to pull it out of the hanger. It's either a two man job or I will need a tug set up. Using various lengths of "L" channel, a triangular pull bar set up is used along with quick release pins and an extended tongue arrangement that allows the tractor to easily pull out the aircraft. Using a forward mounted hitch allows the tug operator to carefully view wing clearance as the the aircraft is pulled out and vice versa when you put it back in the hanger.

When the Kiddy Copter needed an instrument panel I researched the Robinson R22 helicopter panel and found a very similar...
16/02/2020

When the Kiddy Copter needed an instrument panel I researched the Robinson R22 helicopter panel and found a very similar shaped Instrument pod for Ultralights available on eBay. The problem was, it was too deep. My plan was to float the pod one half inch from the inside of the bubble. I first located the front panel of the pod on the inside of the bubble with strings and tape and then projected a geoconcentric line onto the pod case. After cutting away the unwanted end I next placed 6 fiberglass cloth layers one at a time onto a 30 inch diameter ball and taped off the shape on the ball and did a fiberglass layup. After curing, I outlined the shape on the inside of the layup, cut it out and used fiberglass tapes from the inside of the pod to cement on the new shape. I used Bondo and carefully sanded the shape until it was nicely blended in with the original shape. Painting, wiring, and attachment to the bubble followed.

15/02/2020

The Kiddy Copter Instrument Panel was inspired by the Robinson R22 Beta Flight Deck. The Guages are simulated using recessed faces with glass and bezel trim but are not functional. Our young pilots can turn Power On using the Master Switch and also switch the left and right batteries.
There is a Engine Start Switch that activates a Helicopter sound card that is controlled by an engine boost switch that controls the Helicopter volume. Other switches control the Navigation Lights, Rotating Beacon, Strobes and the Camera and Monitor. There is also a functional compass atop the panel.

I found a little kids go-kart from China that had good bones for the Kiddy Copter project and then I hacked it removing ...
06/02/2020

I found a little kids go-kart from China that had good bones for the Kiddy Copter project and then I hacked it removing the front wheels, steering wheel etc. I kept the seat, rear wheels, pedals and chain drive only. Then I got a giant ball to help resemble the bubble giving dimensional info to order a custom made bubble. From there I tack welded on the custom made hoops, the skids, the nose wheel etc. then I fabricated the steel tail boom with all the cross braces and then tack welded the entire assembly together. Then Tony with his superior welding skills completed the finished welds and made it ready for sandblasting and painting.

I originally created N728DC as an air ambulance from it's heritage as a World War 2 patient transporter.  The unique rai...
05/02/2020

I originally created N728DC as an air ambulance from it's heritage as a World War 2 patient transporter. The unique raised turtle deck was first operated with a hand crank hydraulic system but I later updated it with an electric ball screw mechanism.

Address

MI

Telephone

(616) 285-5907

Website

Alerts

Be the first to know and let us send you an email when Cleared To Land posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Cleared To Land:

Shortcuts

  • Want your business to be the top-listed shop?

Share