Loaded Chamber

Name: Loaded Chamber
Address: 826 Office Park Circle Suite 104, Lewisville, TX, 75057, US
Telephone: +19722195510
Price range: $$

Loaded Chamber is a custom gunsmithing services shop. Located in Lewisville, TX. Loaded Chamber is a

05/25/2026

This MAC 9DS had some slide machine work and barrel porting done. An additional serration and window were machined forward of the factory machined cuts. The barrel was ported in each cut centered in the windows and at a 25 degree angle. The barrel is coated on Gold Cerakote and the slide is a simple Black Multicam. The grip module and mainspring housing were reduced for better grip. The grip safety was pinned in place at the mainspring housing. Then the grip was stippled in wagon wheel texture.

05/16/2026

MP5SD kit build. Built from a flat. The housing was clipped and pinned. The pack was converted to safe and semi only. A pic rail was welded for optics. Metal and suppressor are coated in Coyote Cerakote.

05/07/2026

This upper in 6mm ARC had a combo block made out of a Superlative Arms piston conversion adjustable gas block and an A2 front sight. The A2 gas system and rear ring were cut and machined off. The rear of the sight was milled to fit the Superlative gas block and positioned where it would be on a standard A2 sight. The block and sight were welded and blended. The front of the A2 sight post was milled to allow gas adjustment and piston removal. The rail was machined for the new combo block. The block and barrel were coated in Graphite Black Cerakote.

04/18/2026

Polish KBK wz. 1960 Kit built on a Tortort receiver and AK Builder barrel. Finished in manganese parkerizing.

04/10/2026

The rear end folding trunnion conversion on this 5.45 Saiga was done by another shop. They had left deep grind marks in the receiver that were really noticeable after the finish was applied. The rear trunnion was demilled and the grind marks cleaned up then rear trunnion was re riveted. The front end had a pin and welded combo block and faux 4 piece flash hider barrel extension pin and welded done by the previous shop. The client got a new combo block and form one’d the rifle. New combo block was installed and pinned. The old selector marks were removed and the Russian marks laser engraved and selector notches were cut. Lastly all metal was coated in Russian paint.

03/24/2026

This Arsenal Sam7K got the muzzle threaded in 1/2x28. The gas block threads were parted off and then the block was turned down and chamfered. The owner wanted to direct thread the suppressor and was already set up for 5/8x24 so a thread adaptor was installed and timed. With the thread protector on it almost looks like a standard block with no device attached.

03/09/2026

This Dan Wesson Valkyrie had the slide tri-topped. The new flat on top had 40 LPI serrations milled in. The optic machine work removed the factory rear sight so a G***k suppressor height was milled in behind the optic. Front cocking serrations were milled in to match the factory rear. 2 small windows were milled on each side at the same angle and in front of the serrations and chamfered. One small window on top behind the front sight was milled in. The barrel was flushed to the bushing and a 45 degree crown cut. The slide was coated in black out Cerakote and the side flats and the 45’a were polished. The frame had an aluminum pic rail machined and welded to the frame. Ideally getting the rail close to where it would be on a factory railed frame. The magwell and grip safety were fit to the frame and blended. Once the frame work was done it was coated in Mystique Cerakote and the controls are all glass bead blasted.

02/19/2026

19X slide machine work and Cerakote. The Acro was milled in between the rear sight and breach. Three angled cuts on top front between the sight and election port angled forward. Recesses were milled in to remove some of the factory engraving. Front cocking serrations and windows were also machined on each side in front. The slide and frame are coated in Troy Coyote Tan.

02/09/2026

FN FNX 9 slide milled for the Acro cut. The optic was milled low enough to co witness after the front portion of the rear sight was milled off. Slide is coated in Sniper Gray Cerakote.

01/27/2026

Type 68 NK kit build on a Childers Guns receiver and an AK Builder barrel. The receiver and barrel are blued and distressed to match the other parts in the kit.

Address

826 Office Park Circle Suite 104
Lewisville, TX
75057

Telephone

+19722195510

Website

http://LoadedChamberTX.com/

Alerts

Be the first to know and let us send you an email when Loaded Chamber posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Loaded Chamber:

Shortcuts

Want your business to be the top-listed Shop in Lewisville?