Experimental Prototype

Experimental Prototype - Light years ahead - Lightweight Custom Bikeparts
Turning your lightweight dreams into reality...

Litet projekt på min lediga tid.
04/07/2025

Litet projekt på min lediga tid.

Hej på er alla. Det har varit tyst här i ett tag. Inte för att jag fått för lite att göra. Tvärtom. En hel del. Jag får ...
04/03/2024

Hej på er alla. Det har varit tyst här i ett tag. Inte för att jag fått för lite att göra. Tvärtom. En hel del. Jag får säga TACK till er som anlitar mig.
Jag har sedan starten för 15 år sedan gått den extra milen och hämtat och kört ut till de som behövt det.
Det här är veckans utkörning som innebär en nätt rund körning på cirka 70 mil. Det görs med en fullastad bil och flera kunder i ett svep. Miljöarbetet finns alltid med i mina tankar från start.

/Mattias

Got a shock link with worn out holes for shock bolts. Bored out in the mill. Made new brass bushings in the lathe, glued...
15/12/2023

Got a shock link with worn out holes for shock bolts. Bored out in the mill. Made new brass bushings in the lathe, glued them in with a dowel for an in line placement. Now out to a bike shop. Better than buying a new frame as these stuff is not in stock.

Trek Emonda topper. Inside diameter 30mm .The top is a modified one which adds 100mm from the small one below.
20/08/2023

Trek Emonda topper. Inside diameter 30mm .
The top is a modified one which adds 100mm from the small one below.

BMC sSpeedfox with internal dropper did break there the dropper ends. Maybe a design flaw with glue joint and open hole ...
17/07/2023

BMC sSpeedfox with internal dropper did break there the dropper ends. Maybe a design flaw with glue joint and open hole in under the junction between top and seat tube.
Did a good paint match on all big and minor damages on that side. Regreased pivot points and tightened dropper cable so it works again. At no extra cost.

Just made aircan/sleeve service and reset IFP on this shock. I just took my cheapest shock and tried to service. Thats a...
21/02/2023

Just made aircan/sleeve service and reset IFP on this shock. I just took my cheapest shock and tried to service. Thats a job that require clean and good tools.
If you feels its a bit difficult. Do support your local bike shop and let them service your bike.
Two more shocks next.

A Trek Top Fuel with a loose linkage mount and stuck screw. Removed and bonded in again with carbonweave. A tricky one b...
11/01/2023

A Trek Top Fuel with a loose linkage mount and stuck screw. Removed and bonded in again with carbonweave.
A tricky one but end result is good.

Did some witchcraft with big help from Giovanni at Elite. Did one training session with a silent and full span of resist...
20/10/2022

Did some witchcraft with big help from Giovanni at Elite.
Did one training session with a silent and full span of resistance. Will be handy when the outdoor season ends.

Made a steerertube in 7075 alu to replace Futureshock front damper  in Specialized road bikes. Weight 120 grams with pot...
15/09/2022

Made a steerertube in 7075 alu to replace Futureshock front damper in Specialized road bikes. Weight 120 grams with potential to much lower.

New idler wheel for my Shan DH project. Hopefully it will not fall off anymore.
01/08/2022

New idler wheel for my Shan DH project.
Hopefully it will not fall off anymore.

A threaded inser came loose. Reglued with some carbon and tightened to 15nm. Seems to hold up nice. One bike saved and a...
08/07/2022

A threaded inser came loose. Reglued with some carbon and tightened to 15nm. Seems to hold up nice. One bike saved and a happy customer. The season is short.

Adress

Björkvagen 26
Insjön
79340

Öppettider

Måndag 06:00 - 18:00
Tisdag 06:00 - 18:00
Onsdag 06:00 - 18:00
Torsdag 06:00 - 18:00
Fredag 06:00 - 18:00
Lördag 06:00 - 18:00
Söndag 06:00 - 18:00

Telefon

+46735311855

Aviseringar

Var den första att veta och låt oss skicka ett mail när Experimental Prototype postar nyheter och kampanjer. Din e-postadress kommer inte att användas för något annat ändamål, och du kan när som helst avbryta prenumerationen.

Kontakta Affären

Skicka ett meddelande till Experimental Prototype:

Dela