Made In Cobham

03/11/2026

November’s our busiest month yet 🎄 Christmas fairs, markets and a fireworks night across Surrey, all with our 3D printed sensory toys, dragons and stocking fillers on the table.

📍Fri 6 · Kingswood House School Fireworks, Epsom, from 6:30pm
📍Sat 7 · Leatherhead Market, 9am–4pm
📍Sun 8 · Winter Market at Denbies, Dorking, 11am–4pm
📍Sat 14 · Parkside Christmas Fair, Stoke D’Abernon, 10am–3pm
📍Sat 14 · St John’s School Christmas Fair, Leatherhead, 10am–2:30pm
📍Sat 21 · Leatherhead Market, 9am–4pm
📍Fri 27 · Hartfield House, Leatherhead, 2–4pm
📍Sat 28 · Leatherhead Market, 9am–4pm
📍Sat 28 · Sir William Perkins’s Christmas Fair, Chertsey, 11:30am–3:30pm
📍Sat 28 · Shrewsbury House Christmas Fair, Surbiton, 12–3pm
📍Sat 28 · City of London Freemen’s School, Ashtead, 11am–2pm
📍Sun 29 · St James’ Christmas Festival, Weybridge, 12–5pm

Save this so you know where to find us – which one will we see you at? 👇

03/11/2026

01/11/2026

From empty pitch to queue in under 5 seconds 🎃
Thank you, Leatherhead. The Ugly Bug Ball was brilliant.

Next up: Kingswood House fireworks, this Friday 6th November. Come and find us.

New here? Follow along for the stalls, the prints and the odd printer emergency 😅

01/11/2026

From empty pitch to queue in 60seconds 🎃
Thank you, Leatherhead. The Ugly Bug Ball was brilliant.
Next up: Kingswood House fireworks, this Friday 6th November. Come and find us.
New here? Follow along for the stalls, the prints and the odd printer emergency 😅

31/10/2026

Skeleton mode: activated 💀
Getting ready for the Ugly Bug Ball at the Swan Centre in Leatherhead today. We're there from 2pm to 6pm with all the spooky specials, so come and find us (and tell us if the costume's working).
Rate the outfit out of 10 👇

29/10/2026

Totally in awe of Bambu Glow 🐍
I bought every colour, then a UV light, and now I can't stop watching the Crystal Snake change colour.

Designed by
Printed on H2D
Filament - Bambu Glow Orange

Which colour should we print it in next? 👇

28/10/2026

Came back to the printers to find a full plate of spaghetti instead of an army of cape flying animals.
In 3D printing terms that's when a print comes loose from the bed and the printer keeps going anyway, piping filament into thin air.

The culprit this time: glue adhesion. The first layer didn't grip the bed properly, so the whole print let go partway through. Fresh glue, clean bed, and it's back on the printer.

Not every print makes it. Every one that reaches the stall has passed the spaghetti test. What's your worst 'that didn't go to plan' moment this week?"

28/10/2026

We're on Leatherhead High Street until 3pm for the Halloween Creepy Crawly Carnival

🎃 Spooky fidgets, dragons in their Halloween best, and plenty to try before you buy. Come and say hello – little monsters very welcome. 👻"

27/10/2026

New here? Let us introduce ourselves 👋

We've started sharing our story in short pieces to camera: who we are, why we make what we make, and what goes on behind the stall.

Follow along to hear it, one chapter at a time.