T-bone Shipwrighting

T-bone Shipwrighting We provide firearm services, focusing on vintage service rifles and precision rifles. Services that
(3)

What else have we got for you? How about a beaut little FN .22 relined and chambered and ready for the extractor cut and...
02/06/2026

What else have we got for you? How about a beaut little FN .22 relined and chambered and ready for the extractor cut and crown tomorrow.
Then we’ll press you back in with some Loctite, dowell pin you for timing and hot blue you!!

No8 furniture getting some reconfiguration for a big-boy calibre. 🥳
02/06/2026

No8 furniture getting some reconfiguration for a big-boy calibre. 🥳

Rem 700 rebarrelled with a Lothar Walther Feinwerkzeugbau GmbH .224-7", #2300-26 (M24) profile barrel, chambered in 223...
02/06/2026

Rem 700 rebarrelled with a Lothar Walther Feinwerkzeugbau GmbH .224-7", #2300-26 (M24) profile barrel, chambered in 223WYLDE, 26" finished with recessed 90° crown and chamfer, cerakoted in Cobalt H112, with Microslicked bolt.

Sometimes an outcome for many reasons can just suck, like these 50m groups.This SMLE Sporter came in for a check over, b...
01/06/2026

Sometimes an outcome for many reasons can just suck, like these 50m groups.
This SMLE Sporter came in for a check over, bedding and range test. The rifle is bedded very nicely, anything that could be checked and corrected has been checked and corrected and the rifle is setup right.
It shoots very poorly.
We will try to get to a better resolution than this, but it’s important that clients know that we charge for the work regardless.
In this case as in many cases the outcome is not entirely within our control. There are aspects of a rifle which we cannot manipulate that can kill accuracy. Sometimes we will be able to identify them other times it’s just like having a lemon of a car.
It’s a genuine reality to be aware of, and to bear in mind.

No4 7.62 coming together, surface grinding a bolthead is a legit way to pickup a thou or 2. Extractor cut made. Foresigh...
29/05/2026

No4 7.62 coming together, surface grinding a bolthead is a legit way to pickup a thou or 2. Extractor cut made. Foresight block soldered on.
And I got the privilege of Raising my good mate and shooting buddy Steve last night.
Today’s a cruise with my 30th high school reunion this afternoon. So if you have any problems today: Don’t call me 😉
So all in all a cracking week.
Enjoy the weekend!

Would have been great to get there on the first time round but we’ve remade this Nielsen MN600 pic rail to suit the clie...
28/05/2026

Would have been great to get there on the first time round but we’ve remade this Nielsen MN600 pic rail to suit the clients requirements.
If anyone needs a nice 20MOA pic rail to suit a MN600 flat top that’s a bit taller than this give me a shout I’ve got one going cheap😘

We are ready to pull this beast apart and blue her, having fitted the mounts collimated the sight and “permanently” fixe...
28/05/2026

We are ready to pull this beast apart and blue her, having fitted the mounts collimated the sight and “permanently” fixed the rings to the tube.
These are a lot of work to get right. And the tricky bit isn’t always the tricky bit you anticipate being the tricky bit…. So tricky….😮‍💨

AI AT, 27mm tennon prefit going out in Lothar Walther Feinwerkzeugbau GmbH stainless, .30-10”, #4120-32 standard Palma,...
28/05/2026

AI AT, 27mm tennon prefit going out in Lothar Walther Feinwerkzeugbau GmbH stainless, .30-10”, #4120-32 standard Palma, 308 throated for something ungodly, recessed 90 degree crown with chamfer, bright linish and away we go.

Bit of rework off the back of sub-optimal comms… we’ll work on it.Setting up one serious ELR optic.338 Lap Mag barrel re...
26/05/2026

Bit of rework off the back of sub-optimal comms… we’ll work on it.
Setting up one serious ELR optic.
338 Lap Mag barrel ready to go, and some tooling on the way out.
That’s all she wrote!

Tikka T3/T3x prefit ready to go out. This fella is a 6mmBR on a Lothar Walther Feinwerkzeugbau GmbH stainless, .243-8", ...
25/05/2026

Tikka T3/T3x prefit ready to go out. This fella is a 6mmBR on a Lothar Walther Feinwerkzeugbau GmbH stainless, .243-8", #2260-26 Re*****on Varmint Contour, muzzle threaded 5/8*24UNEF and capped with our simple knurled ally thread cap.
With our on the shelf blank options we can prep and dispatch a lot of prefit options or fit them to your actions pretty quickly. If you have custom requirements or requirements that are not on the shelf we can order in exactly what you require and gett'er done.
Our next new order will be placed in end of June and we're hoping for delivery in November, so shoot us an email if you want to get something special.
Reamers are constantly being ordered and the current lead times are reasonable.
We would love to build your project, fit your barrel, setup your prefit, supply your tooling and very soon do your Cerakote in house.

Address

Moorebank, NSW
2170

Opening Hours

Monday 6am - 3pm
Tuesday 6am - 3pm
Wednesday 6am - 3pm
Thursday 6am - 3pm
Friday 6am - 3pm

Telephone

+61291378928

Website

Alerts

Be the first to know and let us send you an email when T-bone Shipwrighting posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to T-bone Shipwrighting:

Shortcuts

Share

Category